1. Rated voltage: 24KV;
2. Rated lightning impulse withstand voltage: 125/145 KV;
3. Rated short-time power frequency withstand voltage: 65/79KV;
4. Rated short-circuit current duration: 4s;
5. Rated frequency: 50Hz.
1. Equipment: XSL225-2C spinner;
2. Part No.: G1
1. Rated impact withstand voltage: 6000V;
2. IP grade: IP30;
3. Pollution grade: 3;
4. Installation type: III;
5. Number of poles: 2/3/4 optional.
6. Action current: 30mA/100mA/300mA (63A/100A/200A housing), 100mA/300mA/500mA (400A housing), 100mA/300mA/500mA/1000mA (800A housing).
1. Explosion-proof mark: ExdⅡBT4;
2. Motor power: 120W;
3. Rated voltage: 220V/380V;
4. Air flow: 2200m³/h.
1. Explosion-proof sign: Ex dellBT4 Gb Ex dellCT4 Gb.
2. Rated voltage: AC 220V.
GB3836.1 GB3836.2 IEC60079
1. Type: PC11;
2. Convert alternating voltage produced by generator to direct voltage required by generator excitor. This plate includes two rectified current, one is bridge rectifier, the other is silicon controlled rectifier, the two rectifiers can automatic transfer;
3. When generator is launched, because the remannence voltage of the generator is too low, the bridge rectifier curcuit can built generator voltage immediately to, external battery and attachments are not needed;
4. When generator voltage arises to a certain level, the silicon controlled rectifier control curcuit will automatically replace the bridge rectifier cercuit to ensure the safety and reliability of the generator excitation curcuit;
5. When generator functions well, it will form an inner ring controlled by closed-loop with AC module to maintain a 600V AC voltage for the generator;
6. When a sudden load change of the generation set occurs, it will form a outer ring controlled by closed circuit with AC module to steadily adjust the exciting voltage, the voltage will be recovered to its set value in a short time;
7. Excitation output:0110 DC voltage signal.
1. API Spec 4F Petroleum Drilling Machine and Rig and Service Specification; 2. API RP500B Recommended Practices on Classification for Petroleum Facilities and Electric Power Device Site; 3. IEC60079-0 General Requirements on Electrical Equipment used for Explosive Gas Environment; 4.GB/T 3797-2005 Electrical Control Equipment; 5.GB7251.1-2005 Low-Voltage Switchgear and Controlgear Assemblies;
1. Medium Temperature: 0-100℃.
2. Contact Capacity: 3A/250VAC.
3. Contact Category: SPDT.
4. Pipeline Requirement: 1-6″.
1. Input: Thermocouple K-type, E-type, B-type, S-type, T-type, J-type, N-type RTD Pt100 Cu100 Cu50 (three-wire or four-wire system)
2. Output: Output 4~20ma DC signal within the range. Linear with the millivolt signal input by thermocouple; linear with the input resistance signal of the RTD. Or linear with temperature signal. As an isolation temperature transmitter, input and output phases are isolated with isolation voltage of 0.5KV, increasing resistance to common-mode interference, more suitable for use with computer networking.
3. Basic error: *±0.5% F・S
4. Transmission method: two-wire system
5. Display mode: (digital) LCD four-bit display, show a sign of e ... when open circuit of thermocouple occurs with output greater than 20mA
6. Working power: Min. voltage of transmitter working power is 12V, Max. voltage 35V, rated operating voltage 24V.
7. Load: Limit load resistance is calculated as follows:
RL (max)=50 (Vmin-12) (i.e. at 24V,
load resistance can be selected within 0～600Ω)
Rated load 250Ω.
8. Normal operating environment:
a) Ambient temperature: -25°C~80°C (Regular type)
-20°C~70°C (Digital display type)
b) Relative humidity: 5%~95%
c) Mechanical vibration: f≤50hz, amplitude <0.15mm
d) In ambient air, there is no corrosive medium for chromium, nickel coating, non-ferrous metals
and other alloys.
9. Impact of ambient temperature: ≤0.05/1°C
Note: "*" Contracted products with a tolerance error of ±0.2% can be provided if specially requested by customers.
10. Mount: regular type, dedicated type, wall mounted type and guide rail type
1. Type: HEP15, JIS explosion-proof type, HEP16, JIS intrinsic safety type, HEP waterproof type;
2. Input signal: 4-20mA.DC, 4-12mA.DC, 12-40mA.DC, 10-50mA.DC(HEP15);
3. Output characteristic: linear, equal percent, quick opening;
4. Input resistance: 250±10Ω(（4～20mA.DC）, 100Ω(10～50mA.DC)
5. Gas supply pressure: 10-160, 120-500KPa;
6. Gas consumption: 4L/min (under 140KPa of gas supply pressure and steady state);
7. Flow: max. 110L/min ((under 140KPa of gas supply pressure and steady state);
8. Air source joint: Rc1/4 (American system), 1/4NPT internal thread;
9. Environment temperature: -40-+80°;
10. Stroke: 10-100mm, 6-10mm (optional);
11. Relative humidity: 10%-90;
12. Material of shell: aluminum alloy;
13. Conductor joint: G1/4;
14. Shell structure: HEP15: explosion proof level d ll BT4, in conformity to GB3836.1,3836.2-83 standard, IP54 is adopted for shell protection, complies with GB4208-84 standard, intrinsic safety level lb ll CT5, meets the GB3836.1,3836.4-83 standard; protection level of shell is IP54, complies with GB4208-84 standard;
15. Limit of basic error: not greater than ±1% of the whole stroke;
16. Dead zone: not greater than 0.1% of the whole stroke;
17. Speed: 4mm/s (HA2D.R type actuating mechanism);
18. Outline dimension (mm): (1*b*h) 380*165*223;
19. Weight: 3.5kg;
1. Model: YT1000R (rotary type);
2. Type: single action, double action;
3. Input signal: 4-20mA DC below 24V;
4. Resistance: 250±15Ω;
5. Gas supply pressure: 1.4-7kgf/cm3 (20-100psig);
6. Stroke: 0-90°;
7. Guide pipe interface: PT(NPT)1/4;
8. Pressure gauge interface: PT(NPT)1/8;
9. Guide pipe: PF1/2;
10. Explosion proof grade: ExiallBT6, ExdmllBt6;
11. Protection grade: IP66;
12. Environmental temperature: -20°C-70°C;
13. Linearity: ±2%;
14. Lagging degree: 1%;
15. Sensitivity: ±0.5%;
16. Repeatability: ±0.5%;
17. Air consumption: 3LPM(Sup=20Psi);
18. Flow: 80LPM (Sup=20Psi);
19. Material: casting aluminum;
20. Weight: 2.8Kg (Approx);